







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Master Halco Fence Installation in Kendale Lakes: What to Know First
We install and repair Master Halco fence systems for Kendale Lakes homeowners, and most residential jobs run $3,500 to $9,000 depending on material, linear footage, and gate count. A straightforward wood or chain link run is often two to four days of work; vinyl and ornamental aluminum take a bit longer once posts cure and gates are hung. We’re an independent Master Halco service provider, which means we buy and install their products but aren’t authorized or backed by the manufacturer – and we’ll say so plainly, because you’re trusting us with a fence line that has to survive South Florida heat, rain, and wind.
This page is for the homeowner who already has a Master Halco estimate, a partial install a previous crew abandoned, or an existing fence that’s failing in a way that doesn’t match what the brand promised. If that’s you, call us at (844) 834-8961 and we’ll walk the property before we quote a number.
How Master Halco Products Fail – and How We Fix Them
Master Halco is one of the largest fence manufacturers in North America, and their lines show up all over Kendale Lakes – the Estate and Elite vinyl series, the Galvanized and ColorBond chain link systems, and their aluminum ornamental profiles. Their products are solid, but “solid” doesn’t mean “immune.” Here’s what we actually see on Kendale Lakes properties, and what we do about it.
- Vinyl post sag at the gate frame (Estate and similar profiles). In Kendale Lakes, the daily summer heat and afternoon storms swing humidity hard. Vinyl posts that were set in a shallow or sandy footing will shift, and the gate-side post is where you’ll notice it first – the gate drags, the latch stops catching, the frame distorts. Master Halco’s own install guidance calls for deeper footings in loose soil; many subs skip it. We re-pour the footing to spec and re-hang the gate rather than just slapping on a latch fix.
- Chain link tension loss after wet season (Galvanized series). Galvanized chain link is tough, but tension bars and bands can loosen as the soil around the posts settles after heavy rain. Homeowners notice a “hammock” sag in the middle of a run. The fix isn’t a new fence – it’s re-stretching the mesh, resetting the tie-wires, and checking every post for true vertical.
- Rust at the weld points on ColorBond (where the coating chips). ColorBond’s bonded coating is a genuine advantage over bare galvanized, but the coating is only as good as the installation. A cut end that wasn’t re-touched, or a ring driven in with a tool that nicked the coating, will start to bleed rust within a season in our humidity. We seal cut ends and swap damaged fittings instead of hoping it holds.
- Wood picket and rail rot at the ground line (Master Halco’s wood and cedar lines). South Florida’s wet-then-dry cycle punishes the bottom of any wood fence. The rail ends and post bases hold moisture longest. We set posts with proper gravel drainage and use pressure-treated or composite components where the original spec called for cedar – a decision we’ll explain before we touch anything.
- Aluminum ornamental gate hardware loosening under wind load. The aluminum ornamental profiles are strong and light, but the hinges and latches are the wear point. After a couple of storm seasons, self-closing hinges drift and latches stop aligning. We replace the hardware with quality aftermarket steel where the OEM hardware can’t keep up – and we’ll tell you when OEM is the better call.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Our Master Halco Fence Installation Process
Every Master Halco job starts with a walk-through, not a sales pitch. Here’s what our process looks like from the first call to the final cleanup.
- 1
Site visit and diagnostics. We walk the property line, check for existing Master Halco components worth saving, measure linear footage, identify utility locates, and look at the soil and slope. This is where we catch the footing problems that cause half the failures we see later.
- 2
Parts decision, in writing. OEM Master Halco components vs. quality aftermarket for hinges, latches, tension bars, and fasteners. In some cases OEM is the only right answer; in others, an aftermarket steel hinge outperforms. You get the comparison on paper before you approve.
- 3
Footing and post set. We set posts per manufacturer spec for depth and concrete, with drainage in mind for Kendale Lakes’ water table. This step can’t be rushed – a perfect fence over a bad footing is a future repair.
- 4
Install or repair. Rails, mesh, pickets, panels, gates – installed clean and true. Perimeter fences go up section by section with a level on every post.
- 5
Gate test and full walk-through. Every gate gets opened and closed a dozen times. We check for sag, drag, and latch alignment, then walk the entire fence line with you before we call it done.
- 6
Cleanup and the 730-Day Done Right Promise. Haul-out, sweep, and a written guarantee that covers workmanship for 730 days – if it’s not done right, we make it right.
See the difference
Before
After
Before
After
Before
AfterWhat Master Halco Fence Installation Costs in Kendale Lakes

Most full Master Halco residential installations in Kendale Lakes fall between $3,500 and $9,000. The low end is a standard chain link or wood run on a straightforward lot; the high end is a long ornamental aluminum or premium vinyl perimeter with multiple gates. Here’s how the numbers break down:
| Scenario | Typical Range |
|---|---|
| Chain link, standard residential run | $3,500 – $5,500 |
| Wood fence, full perimeter with one gate | $4,500 – $7,500 |
| Vinyl (Estate/Elite series), full perimeter | $5,500 – $9,000 |
| Aluminum ornamental, with gates | $4,000 – $10,000 |
| Partial repair / re-stretch / re-hang gate | $350 – $1,800 |
What moves the price: linear footage, gate count, material grade (vinyl thickness matters), and site conditions – slope, old-fence tear-out, and footing depth on sandy lots. Our quotes are upfront with no surprises; the number you see is the number you pay. Most estimates come back free and in writing within a few days of the walk-through. Call (844) 834-8961 to book your free estimate.
Why Kendale Lakes Homeowners Call Groundwork Construction Co. of Kendale Lakes for Master Halco Work
We’ve been installing and repairing fences in Kendale Lakes long enough to know which Master Halco lines fail where and why, and we put that knowledge on paper with a 730-Day Done Right Promise that’s one of the longest workmanship guarantees in the residential construction space. Technicians have up to 12 years of experience, they’re background-checked, and they show up in uniform – not out of an unmarked van. Calls are answered by a live person, 24/7, so you’re not waiting until Monday when a gate falls off its hinge. Fencing is one of seven trades we handle, so if you’re also planning a kitchen, bathroom, or window upgrade, the same trusted partners – KraftMaid, Kohler, GAF, PGT – are already on our roster. From foundation to finish line, one contractor, one guarantee.
FAQs

Most likely not for installation-related failures, and it depends on the specific series and whether the original installer was authorized. Master Halco’s manufacturer warranty typically covers product defects, not footing settlement or gate sag caused by a bad install. As an independent Master Halco service provider, we can’t file a manufacturer claim on your behalf, but we can tell you in ten minutes whether the problem is a product issue or an installation issue – and quote the fix either way. Call (844) 834-8961 for a free look.
Usually repair. Chain link tension loss, vinyl post sag, and gate hardware wear are all fixable without replacing a full perimeter. Replacement makes sense when more than a third of the posts are compromised or the fence is past its material life. We’ll give you both numbers so you can decide.
For most components, yes – OEM is the right call for tension bars, tie-wires, and vinyl fittings. For gate hardware like hinges and latches, a quality aftermarket steel part sometimes outlasts OEM in our humidity. We’ll put the comparison in your written quote so you’re not guessing.
A standard residential run is two to four days of work once materials are on site, and material lead time is typically one to two weeks for most Master Halco series. We book the walk-through first, so we can give you a real timeline in the estimate – not a guess over the phone.
Not under our pricing – the number you see on the written quote is the number you pay. If we find buried utilities, hidden concrete, or a footing condition nobody could see on the walk-through, we stop, document it, and talk to you before any extra cost. Call (844) 834-8961 for your free estimate.
Whether you’re replacing a sagging Master Halco chain link run, repairing a vinyl gate that won’t latch, or installing a fresh ornamental aluminum perimeter, we’d rather walk the property and give you a straight number than talk in circles on the phone. Call Groundwork Construction Co. of Kendale Lakes at (844) 834-8961 to schedule your free estimate. Backed by our 730-Day Done Right Promise, upfront pricing, and a live person on the other end of the line around the clock.
Written by the team at Groundwork Construction Co. of Kendale Lakes, serving Kendale Lakes and nearby areas.












