







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterHow to Measure a Window for Replacement in Kendale Lakes, FL: It Starts at the Rough Opening, Not the Glass
For a window in a Kendale Lakes CBS home, the measurement that actually matters is the masonry rough opening, not the size of the existing frame. Most replacement orders go wrong because the new unit gets sized to the old frame, when in 1970s concrete-block construction that frame is often “in-frame” rather than “in-opening” and sits a half inch or more off from the true opening. Get the rough opening, the existing frame, and the daylight opening all documented, subtract the High Velocity Hurricane Zone clearance, and you have a number a window can actually be built to. Most homeowners in Kendale Lakes shouldn’t try to nail that on their own; a proper site assessment does it before a quote is written. Call (844) 834-8961 and we’ll walk you through what your openings need.

Key takeaways
- The masonry rough opening drives the replacement size in CBS construction, not the old frame.
- Wood bucks in 1970s Kendale Lakes homes often vary by 1/2″ or more side to side; you measure to the smallest dimension.
- HVHZ specs call for at least 1/4″ clearance between the new frame and the rough opening so foam seal can go in.
- Miami-Dade permit forms want all three measurements per opening: rough opening, existing frame, daylight opening.
- You don’t have to become a measuring expert. We survey and document openings for permit submittal.

Why the standard “measure the glass” advice fails in a Kendale Lakes concrete-block home
Measure the glass, order the window, install it. That’s the standard advice, and in a wood-frame house it usually works. In a 1970s concrete-block tract home in Kendale Lakes, it will likely produce the wrong window size for the wrong reasons. These homes went up during the transition from pre-Andrew to post-Andrew code, and the openings reflect it: a poured or block opening wrapped in a wood buck, then a window set inside that buck. The buck is what you see. The masonry opening behind it is what the new window has to fit. Those are rarely the same number.
We see this on nearly every impact-window retrofit in the Kendale Lakes subdivisions west of the Turnpike, where the housing stock is fully built out and every job is a renovation rather than new construction. When a homeowner measures the visible frame and hands that figure to a supplier, the replacement arrives undersized for the rough opening and the installer spends the day shimming and foaming to close a gap that shouldn’t have existed. Undersized is the common failure here, not oversized.
The three measurements every Kendale Lakes window opening needs
Miami-Dade permit documentation for HVHZ window compliance wants three distinct measurements per opening. Skip one and the submittal comes back.
- Rough opening. The inside dimensions of the masonry opening with the existing window and buck accounted for. This is the governing number for replacement sizing.
- Existing frame. The visible frame you’d measure if you were following a generic guide. Useful for comparison, and often where the discrepancy shows up.
- Daylight opening. The clear glass area. This matters for egress calculations and for matching the look of the room.
Take width at the top, middle, and bottom of the opening, and height at the left, middle, and right. Then use the smallest figure in each direction. In these 1970s-80s wood bucks, we regularly see 1/2″ or more of variance across a single opening, usually from moisture damage at the sill or a buck that was never square to begin with. A buck that has swollen and checked from decades of South Florida humidity will throw off a top-to-bottom measurement every time. If you measure once at the middle and order to that, you’re guessing.

The HVHZ clearance rule that no standard measuring guide mentions
Miami-Dade’s High Velocity Hurricane Zone installation specs require a minimum 1/4″ clearance between the replacement frame and the rough opening so foam sealant can be applied and the assembly can move and seal as designed. That clearance changes the specified window size. It isn’t in the generic “how to measure a window” advice because most of that advice was written for markets that don’t build to HVHZ code. Here, it’s the difference between a window that passes inspection and one that gets flagged.
Wind-driven rain in hurricane season finds every gap that wasn’t sealed to spec, and a Kendale Lakes home takes that rain on a stucco wall over concrete block with low-pitch roof above. The window has to be part of a continuous waterproofed envelope, not a unit wedged into a hole. That’s why the clearance matters as much as the size.

What a full opening survey captures, and what it costs to fix after the fact
| Item | What it means for your order |
|---|---|
| Rough opening width | Smallest of top/middle/bottom, minus 1/4″ clearance each side |
| Rough opening height | Smallest of left/middle/right, minus 1/4″ clearance top and bottom |
| Buck condition | Moisture damage or rot means repair before the new unit goes in |
| Daylight opening | Egress and appearance check |
| Documentation | All three measurements per opening, ready for Miami-Dade permit submittal |
Window Replacement in Kendale Lakes runs $4,500-$15,000 for a typical home, and Impact Window Installation runs $8,000-$25,000 depending on opening count and product line. A remeasured and reordered unit can eat a meaningful chunk of that budget, which is the real cost of a bad first measurement. We build in Windows & Doors with Andersen and Pella units and back the install with our 730-Day Done Right Promise: if it’s not done right, we make it right.
How Groundwork handles the measuring so you don’t have to
Our pre-installation site assessment includes a full masonry opening survey with documentation ready for permit submittal. Technicians with up to 12 years of experience measure every opening the same way, note buck condition and any stucco repair needed, and hand you a written size spec rather than a guess. Calls are answered by a live person 24/7, and pricing is upfront, so the number you see is the number you pay. When your project runs past $10,000, $1,000 off applies, and 0% financing for 18 months is available on approved projects. More on how we work across the area is on our Kendale Lakes service area page, and you can start from our home page to see the full scope of what we build from foundation to finish line.
- Measure to the rough opening, not the frame in any CBS home in Kendale Lakes.
- Smallest dimension wins when the buck varies by 1/2″ or more.
- Leave 1/4″ clearance for foam seal per HVHZ spec.
- Document all three measurements for the permit.
- Repair the buck before ordering if moisture damage is present.
FAQs
You can get a rough idea, but the number that determines the actual order is the masonry rough opening, and that requires getting behind the existing frame and assessing the wood buck. If you’re only measuring the visible glass or frame, you’ll likely order undersized. For an accurate spec, it’s worth having the opening surveyed and documented.
Wood bucks in 1970s-80s CBS construction often have moisture damage or dimensional inconsistency, so width at the top, middle, and bottom can differ by 1/2″ or more. You measure all three and use the smallest, which is why a single measurement at one height gives you the wrong size.
HVHZ installation specs call for a minimum 1/4″ clearance between the replacement frame and the rough opening so foam seal can be applied. That clearance changes the specified window size and isn’t part of a standard measuring guide. Call (844) 834-8961 for an exact quote on your openings; estimates are free.
We schedule site assessments quickly and answer the phone around the clock, so a same-day visit is often possible depending on the week. The assessment covers every opening plus documentation for the permit. Call (844) 834-8961 to get on the schedule.
If you’d rather have it looked at, Groundwork Construction Co. of Kendale Lakes offers a no-pressure assessment in Kendale Lakes. We measure the rough openings, check the bucks, and hand you documentation that matches what Miami-Dade wants to see. Call (844) 834-8961 and we’ll get you an accurate size before you order a single window.
Written by the team at Groundwork Construction Co. of Kendale Lakes, serving Kendale Lakes, FL.


